Repair of machine carpet and its types

What is car carpet repair? For any product, there is a possibility that it will be damaged and worn out. Carpets are no exception to this rule. Machine-made carpets are always prone to wear and tear because they have a lot of footprints and we do our daily work on the carpets day and night, so in the carpet industry there are sub-branches that repair torn, burnt, and discolored carpets. This branch of industry is called embossing. Master Rufogar has the ability to repair both machine-made carpets and hand-made carpets. Carpet is less discolored due to its artificial dyeing; But we often see that the carpet suffers from burns or scratches that the embosser can help to some extent to eliminate these defects. But sometimes it is possible for the carpet to have defects that the car carpet repairs did at home. In this article, we will review these defects and explain the solutions to eliminate them. So follow us to the end of the article.     Repair of burnt machine carpet with charcoal One of the most common injuries to a hot carpet is burning a spot on the carpet. Basically, because people use hookahs and cigarettes at home, or there is a possibility that hot objects are placed on the carpet, it often happens that the car carpet burns. What solution did he take to repair the machine carpet in these cases? prevention It is very likely that charcoal or cigarette ash will be spilled on the carpet, a mistake that most people make in these situations is to remove the charcoal by hand. Because coal is so hot and cannot be picked up by hand, people throw it away at these times. This will spread the hot object all over the carpet. Whenever charcoal falls on the carpet, remove it from the carpet surface with the first tool. Even if your fingers burn, it is better than burning the carpet. The sooner you remove the charcoal, the less the depth of the burn and the greater the possibility of repair. After removing it, if the burn did not cause the carpet to puncture, repair the machine carpet at home. Tip: If you use tobacco at home, it is better to spread a blanket on the carpet so that the carpet does not burn. Restoration method First, gently sand the burn with a soft sandpaper, be sure to sand only the hot spot. Sweep waste and abrasive chips. Using scissors, separate the burnt fibers from the carpet. If there are not many burns, just cut the tips of the fibers, being careful not to puncture the carpet. When cutting the fibers, the possibility of recessing the carpet is very high. If the burn mark remains, clean the black carpet with shampoo. Let some shampoo stay on the carpet. Then gently wipe the carpet with a damp cloth. Note that if the burn depth is high, the carpet burn repair should be done by the embosser. It is important to note that many articles have suggested that you use oxygenated water to repair a car carpet when the carpet has been damaged by objects such as charcoal or cigarettes. This article can not confirm the accuracy of this claim, but warns that the fibers may lose their color in combination with oxygenated water, so it is better not to use oxygenated water.     If you have ironed the carpet, it is better to do the following steps to repair the machine carpet. First, check how much the iron has burned the machine carpet. If it is about to turn yellow, cut an onion in half and place it on the damaged part, this will reduce the yellowing of the carpet. If the fibers cause the fibers to turn black, it is better to send the carpet to embossing. Repairing machine carpet, tearing roots One of the defects that is frequently seen in machine-made carpets is the separation of the roots of machine-made carpets from the carpet structure. Yellowing of the roots of machine-made carpets is another reason why carpets need to be repaired. To repair machine-made carpets, embossing workshops use equipment to remove defective roots and sew new roots to the carpet. In these workshops, using a cutter, first the root of the carpet is cut and then the new root is sewn to the machine carpet using a new rooting machine. When repairing the root of the machine carpet, three inches of the carpet background is reduced. Therefore, you do not need to carve the carpet for repair until it is needed. The repair of machine carpet head is done in the same way. Repairing machine carpet rupture Machine carpet is less prone to tearing; But sometimes it happens that the carpet is pressed against each other for a long time under the pressure and the carpet is torn due to the least lateral pressure. For example, a machine-made carpet is placed under the base of a cupboard or sofa for a long time, and the pressure causes the carpet to become indented. It is possible that the carpet will be torn during washing or if a stretch occurs. In this case, it is better to leave the repair of the machine carpet to the embosser. Usually, embossing masters will tell you whether the carpet is worth repairing or not, seeing the extent of the tear. What is the price of your carpet and what will be the price of the machine-made carpet will determine whether your carpet is worth repairing or not. prevention To prevent this from happening, it is best to place a few thick cardboard bases or plastic bases under pressure on the cupboard bases. Closing remarks: Although the solutions were mentioned and the methods of repair at home were partially stated; But it is better to repair the machine carpet by a master embosser. Carpet embossing is usually done in such a way that the damage is not detectable at all. So it is better to consult a skilled craftsman before doing anything to repair the machine carpet.